Archives

All posts for the month December, 2019

REFURBISHING A USED FRAME

Published December 30, 2019 by Gail Daley Writer & Artist

Framing On A Budget – Part 3

Refinishing FramesThe first thing you are going to need is an outdoor workspace. Refinishing frames is messy, and the materials used need good ventilation. You may also want to invest in a folding table that can be put up when not in use.

MATERIALS NEEDED

To repair a wooden frameyou will need, shop rags, a box knife, painters tape, small can of wood putty, a hammer, screwdriver, small woodscrews, finish nails, glue, wood stripper, paint or stain (probably both), sandpaper (both fine and coarse), a putty knife or plastic scraper, and sponges and brushes for applying the stripper, stain or paint and clear wood varnish. Gloves to protect your hands from the paint stripper and a mask for the fumes are also going to be needed. You may not use all of these; it depends on the type of repairs you are planning to do to the frame.

To repair a metal frame, you will need ), shop rags, sandpaper (both fine and coarse), metal primer, a mask to protect yourself from paint fumes, protective goggles, several cans of spray metal paint (matte finish) and can of clear metal varnish. Gloves to protect your hands from the paint are also going to be needed.

REPAIR & REFURBISHING

Metal Frame: begin by taking the glass or plexi out of the frame and setting it aside in a safe place. You will be re-using it so make sure you put it somewhere it won’t be damaged while you are working. Remove any backing or hanging system attached and examine the frame carefully. Sand out any rust spots using the coarse sandpaper and follow up by smoothing with the fine sandpaper. Depending on the deepness of the scratches you may elect to use either grade of sandpaper to smooth out any scratches. Wipe the frame to remove any excess dust left over from sanding. Lay the frame out flat and spray with primer using a side-to-side motion allow to dry and repeat until completely covered. Do NOT rush this process.Applying too many coats of paint too fast will cause it to run! Allow the primer to dry overnight and repeat process with the metal paint using the same technique on the 2ndday. The next day you may apply the clear varnish. On the fourth day you can replace the glass or plexi into frame andWallah! You have a ready to use frame!

Wood Frame:begin by removing any canvas, hanging hardware and leftover backing paper from the frame. Do any repair work requiring nails or screws and then cover the linen mat with the painters tape, cutting off any excess tape in the corners with the box knife. Remove any sharp edges on the front of the frame by sanding them smooth. If you plan to re-stain the frame, follow the directions on the wood stripper for removing the varnish. This will cause the wood to swell a little bit. Let it dry overnight and then touch up with the sandpaper. Wipe the frame clean of any sanded residue, fill any cracks or holes with wood putty you have prepped by adding the stain to match the color (if you are going to paint over it, it isn’t necessary to prep the wood putty with color). Wipe off any excess stain and allow it to dry overnight (staining may also cause the wood to swell). The next day smooth over any raised edges left over from the stain before applying the coat of clear varnish. Allow the varnish to set overnight. If you have painted the frame you can skip this step, although the extra varnish coat will provide some protection, it will also tend to show scratches later. You are now ready to repair the mat.

The Linen Mat:remove the painters tape from the mat and apply new strips of tape to the newly varnished or painted frame. If there is a dark stain, you may want to apply a small mixture of household bleach to the stain before repainting it. Once the stain is gone, rinse off the bleach with a soft sponge and allow the linen to dry. If the mat is torn use a small amount of glue and press it down firmly, making sure there are no lumps of glue left.

To paint the linen mat I find that Acrylic paints work best. After selecting your color (I prefer either Unbleached Titanium or Parchment) Thin and extend acrylic paint with a textile medium or water. Many artists prefer to a water-soluble medium to produce a smoother finish to the final product. You want the paint to be thin but not runny. Using a small brush, lightly apply several coats of this mixture to the linen mat, allowing to dry between coats. Once you are satisfied with the color remove the painters tape from the wood part of the frame and you are ready to frame your art.

HOW TO CHOOSE A GOOD USED FRAME

Published December 23, 2019 by Gail Daley Writer & Artist

FRAMING ON A BUDGET – PART 2

Another way to frame inexpensively is by restoring used frames. Where can you find used frames? A good source for used frames is flea markets, second hand stores and yard sales.

Choosing A Good Used Frameis not as difficult as you may think. Take your tape measure with you because frames and framed art found here may or may not meet the usual size requirements of the standard canvas sizes sold in the art store. The frame probably won’t be in pristine condition eiher so you may have to do some refinishing. I recommend wood or metal frames because they are easiest to clean up and refurbish. Because of the difficulty of repairing the faux carvings, I prefer to stay away from the more ornate frames with raised plaster designs.

Metal Frames: A good used metal frame may have scratches, but it will be square (no warping) without bent edges. Depending on the size of the art you are planning to frame, it should probably be at least ¾” to 1” wide. Make sure the corners fit together well without any danger of coming apart. A little rust or scratches are okay as they can be sanded off and smoothed out. Check the sizing with your tape measure to be sure your art will fit. Metal frames are typically used to frame watercolors or pastels, which are done on paper, and while the art paper may be cut to fit the frame, pastels and watercolors are also usually presented with a mat. Unless you have a mat-cutter, you will be using pre-cut mats, which come in the same standard sizes as canvas so making sure the frame is a standard size will cut down on the amount of work you will need to do when you frame the art. The used mat mayalso be reusable depending on its condition but if it free from stains this is an easy fix. Scratches on the glass or plexi means it will have to be replaced, although if the glass is scratched very near the edge of the frame it might not be noticed.

Wood Frames: A used wooden frame may or may not come with a canvas painting or print. The good news here is that after you have checked to make sure you won’t be covering up a lost masterpiece, you will also have a blank canvas or board that you can use to paint yourmasterpiece! (Look for a separate blog on re-using canvas).

Non-fixable issues: Check the frame for warping. Warping can be caused by water damage or just simply damage done to the frame itself. While warping can be corrected it requires wood shop tools like vises and such. Probably not worth your trouble.

Chipped Corners or edges: Unless you are going to go for a distressed or really rustic look this can’t be fixed. It can be minimized with paint but it will still show up to the eyes.

Fixable Issues:check for loose corners. This is an easy fix, usually requiring some wood putty and finish nails. Scratches and stains are also fixable requiring stripping, re-sanding and either re-staining or painting of the wood part of the frame.

Linen Mat Issues On A Wood Frame: The most common flaw in a used wooden frame is the linen mat is stained or discolored. This is a pretty easy fix; just repaint it with off-white or parchment color. A tear in the mat may or may not be fixable, depending on the size of the damage. Usually a little glue and repainting the mat will suffice.

*For How-To procedures on refinishing old frames, please see the blog Refurbishing A Used Frame (part 3 of this series).

 

FRAMING ON A BUDGET – PART 1

Published December 16, 2019 by Gail Daley Writer & Artist

Framing fine art can enhance the overall appeal of a piece of artwork; unfortunately, if you don’t frame yourart wisely a poor framing job can ultimately ruin the appeal of the painting or photograph altogether.   We all want our art to look its best, so artists inexperienced in the art of framing usually begin by using a commercial framer. A commercial framer will give you a nice, professional looking frame for your art. They will also give you sticker shock when quoting the price. Depending on the size of the frame wanted, a commercial framer can charge anywhere from $200 to $600 for a simple frame for a painting. Keep in mind that the cost can go much higher if you want an elaborate, ornate frame for your art. Contrary to popular supposition, using a metal frame is not cheaper (metal frames are favored by watercolorists and pastel artists). A commercial framer must not only charge you for the materials, but also for the labor it takes to actually frame the art.

The simplest way to avoid this type of sticker shock is to do your own framing. This isn’t really that hard; the first step is finding an inexpensive frame that looks good. The local art store will have a variety of frames to select from in standard sizes so watch the sales flyers for Coupons from your local art store and use them. Depending on the size of the art you are framing, you may be able to find suitable frames from other sources also. Dollar and discount stores such as Walmart and Target typically have photo frames available in sizes that can be adapted to art. Words of warning here however; makesure that the frames you purchase from this source are made of wood and not plastic or acrylic. Plastic or acrylic frames can’t easily be adapted to the hanging methods required by most art shows. The saw-tooth or eyelet hangers that come with the frames probably won’t be accepted at a professional art show or gallery. Another difficulty is sizing. Take your tape measure with you; some of the frames sold at these places are not the standard sizes used by artists. Frames that look to be 11 x 14 can turn out to be 10 x 13 or some other odd size that won’t fit canvas or canvas boards sold to painters.

Another good source for finding inexpensive frames is On-line catalogs or internet stores. Typically these sites will charge less than your local art store because you are circumventing the middleman’s markup. This is my favorite source when purchasing new frames because the cost is usually 30 to 50% less than that of my local retail store. Of course the shipping does add an extra fee which cuts down on the savings somewhat. I buy frames from these places in bulk once or twice a year because there is an additional discount if you buy at least 3 or 4 frames at the same time. Think ahead and sign up for the stores e-mail program so you will be notified when they are having a sale. If you can’t afford the initial cost of buying in bulk up front, you might consider buying in bulk and sharing the cost with other artists. Some good sources of Catalogs are to name only a few:

ASW (Art Supply Warehouse) http://www.aswexpress.com/,

The Frame Place http://www.frameplace.com/xwoodfrm.htm,

Frame USA http://www.frameusa.com/wood-frames

Another way to frame inexpensively is to find used frames and refurbish them. Where can you find used frames? Well the two main sources I have found for used frames are second hand stores and yard sales. Again, take your tape measure with you because framed art found here may or may not meet the size requirements of standard canvas sizes sold in the art store. The frame probably won’t be in pristine condition so you may have to do some refurbishing and refinishing. Look for wooden or metal frames because they are easiest to clean up and refurbish. This subject is covered in more detail in Part two How To Find A Good Used Frame, Part three of this series on inexpensive framing covers ways to refurbish a used frame, and Part four explains how to refinish one of those ornate frames.

HOW DO YOU LET BUYERS KNOW WHO YOU ARE?

Published December 9, 2019 by Gail Daley Writer & Artist

Promoting yourself as an artist or a writer is hard work. Don’t expect someone else to look out for your interests. Does this promotion time take time away from creating your work? Yes, it does. unless you are very, very lucky if you don’t spend at least some time per week marketing yourself and your work, you will make very few sales.

What methods can be used to promote your art?

There are nuts and bolts types of promotion, flyers, advertising on TV/Radio, etc. And there is the Internet. Flyers and advertising are more time consuming and they cost more money that using the internet. A 1% return response to a typical mail campaign is considered a good response.

Most of the internet is free but typically, a pay-per-click ad on Google or Facebook (an ad where you pay only when a viewer clicks on the ad) is usually around 2 cents a click. The ads run automatically until you run out of the money you allocated. If you are doing your own promoting, to better utilize the time spent on social networks, make a list of what you expect to accomplish to promote your art that day, and then strictly compartmentalize what to do there.

For myself, I schedule 2 hours per week for business. At the end of the two hours I am done, whether or not I actually accomplished everything on my list. The 2ndthing is not to do purely social things while promoting your business. Schedule a different time to catch up with friends and family on your social networking site.

In this day and age, the internet is an essential tool for Artists. Art buyers will often first check out an artist’s website for information before picking up the phone to call directly. A website is also useful because it should show how to contact you. Since the general public now spends an average of 4 hours online daily, why shouldn’t they spend it with your art or your books?

Social networking sites like Pinterest and Facebook now have Business pages you can add to your regular networking sites. There are also plenty of free build-your-own-website hosting sites out there now. Because these sites are supported by the ads they run, ads will appear on your site also. Play around until you find a user friendly one that includes optimizing your site for mobile searches. I recommend Yola.com.

Many authors cross-promote each other’s books to gain visibility with a relevant new audience of readers. It’s a mutually beneficial way to inexpensively boost book sales and word-of-mouth buzz — and to make new friends and build relationships in the publishing community. You can also reach out to other authors in your area and join with them in group book signings. Go to the Local Writer section of your local library and see who has book there. You can then search out their social media sites and their web site to get in touch with them.

There are also sites set up for writers such as www.Bookfunnel.comwhere writers can join with other writers who produce books in the same genre to promote their books. These promotions are usually no charge, but they do require a writer to share the promotion on both social media and with their e-mail list. The site has two distinct type of promotions; one is a newsletter builder (readers sign up to join your list) and the other is a sales promotional page for e-books. FYI the newsletter page involves giving away a free e-book. This is an inexpensive way to encourage readers to join your e-mail list.

 

 

Earning Residual Income With Your Work

Published December 2, 2019 by Gail Daley Writer & Artist

We may as well admit it: all of us secretly want to not only create fabulous art but want the public to appreciate it so much they pay us fabulous prices for it. The wonderful thing about making prints of our work is it a way to earn residual income on our art. If an artist sells a painting for $500 that is a one-time fee; if that same artist also sells 20 prints for $15 each then they have earned a total of $800 on that same painting. Naturally as an artist, you want any reproductions of your art to reflect the quality of the art itself, which means you want to make the best quality reproductions you can find. I have had several artists ask me where they can get good quality prints made at a reasonable price. It’s a good question. There are two ways to go with this: make the prints yourself or get them made professionally.

If you are planning to make them yourself, besides the printer, you will need a good quality camera that takes high-resolution photos (Canon Rebel is excellent but there are others out there). I don’t recommend a point-and-shoot camera or your cell phone if you intend to make professional looking reproductions; although the smart phone photo quality is improving, I did notice that quality seemed to suffer with larger size prints. I would also recommend a good photo-editing program such as Photoshop Elements. I chose Elements because it will service either Apple or PC computers, the basic editing techniques are simple and it does have tutorials.

A printer that prints on a variety of paper products is essential if you are making your own prints. What brand of printer makes the best prints? Well, there are a lot of differing opinions on this, all having to do with what kind of ink will give you the truest colors, how easy they are to use, whether to use ink jet or laser printers, etc. Making the prints yourself does mean that you are probably going to be limited to paper and the sizes you can make; most home printers will only take legal or letter size paper. The printer that gave me the very best prints I ever made at home was an inexpensive Kodak printer. Unfortunately it proved too fragile to last long. Epson, Brother and HP all make good machines that will give you nice paper prints. You can even obtain letter size “canvas paper’ for printing on the internet, although I wasn’t really happy with the quality of the prints I made with it on my home printer. If you are going to make prints yourself, you should consider the cost of the ink. Many ink jet printers devour ink pods like a T-Rex. If you make a lot of reproductions, Ink jet refills can be so expensive that you might find it less costly to get your prints made by a print shop. Laser printers also make good quality prints, but a color laser printer and the toner to go with it can also break your budget. You will need to decide if the cost of the printing will allow you to still make sales at a profit.

The next option is to have your prints made by a professional printer. I am speaking here of commercial printers such as Kinkos or CopyMax’s Impress. The photo departments of Costco, Walgreens, Wal-Mart etc. may not give you a professional quality print because their print programs are designed to “flatten or homogenize” color to an “average” standard, however they also will work with you on this issue because they want your return business. Most of them can also do a canvas print mounted on stretcher bars. Again, ask for a proof because if you have vibrant, saturated or delicate shades you may find your print simply doesn’t reflect these qualities.

To use an outside printer you need a high-resolution jpeg or other type of photo of your work. If you are not a photographer, I suggest you arrange to have a professional take the photo in order to ensure that the photo has no distortions and that the color is true to the original art. You can have the photo transferred to either a jump drive or disc. An issue with having your prints made by someone else that doesn’t come up with DIY (Do It Yourself) printing: calibrating their printer to your photos. Calibrating a printer has nothing to do with the printer type; it has to do with communication between the computer and the printer. Even if the photo from your thumb disc looks okay on their computer screen, the print may still come out darker or lighter than your art. Always ask for a proof before accepting the print because it may be necessary for you to take your disc or jump drive home so that you can adjust the lighting or color of the photo in order to make the print “true” to the original when using an outside printer. If you do this, always save the “adjusted” photo as a separate file and leave the original alone. Making these changes is much easier if you are dealing with a local printer.

The other option for having your prints made is to find a local professional who specializes in making art prints. Here in Fresno we have several but Mullins Photography is the one most favored by local artists. If you bring in your art, they make their own scan and reproduce a print that is virtually identical to the original. Ask other local artists in your area where they get their prints made. Be prepared to open your wallet for this option though; because the cost of the initial set up fee will be more expensive than say Kinkos or Impress. On the other hand, it probably will be a one-time fee for that particular piece of art and the quality will be the best.

You can also order prints from the internet; a number of Internet sites do on-line printing. These sites are sometimes referred to as POD (Print On Demand) sites, and most of them do an excellent job. Fine Art America for instance will not only make your prints on a variety of paper, metal, cards and canvas, but also sell matting and framing and ship to your customer. With on-line printers however, you will have the same difficulties with the calibration as with your local outside printer. Since you can’t demand a proof from this type of site, I would suggest you get a small print made for yourself and adjust the photo. Keep notes on what you did so that you can use them when sending in later prints. The nice thing about most POD sites is your customer may order directly from the site without you having to deal with nasty stuff like figuring out shipping costs.

%d bloggers like this: